Carbide Rotary Burrs can be used cutting, shaping, grinding and also for the eliminating sharp edges, burrs and excess material (deburring) and this is what we should speak about in this article.
For drilling holes or cutting a dent in metal a carbide drill or even a carbide end mill, carbide slot drill or possibly a carbide router is needed instead of a carbide burr. For carving into stone you’d probably ideally make use of a Diamond Burr.
1. Carbide Burrs Can be utilized on Many Materials
Tungsten Carbide burrs works extremely well on many materials: metals including steel, aluminum and certain, various wood, acrylics, fibreglass and plastics. When used on soft metals for example gold, platinum and silver, carbide burrs are perfect because they will last quite a long time without any chipping or breaking.
Steel, Carbon Steel & Stainless Steel
Certain
Aluminium
Titanium
Cobalt
Nickel
Gold, Platinum & Silver
Ceramics
Fibreglass
Plastic, Graphite Reinforced Plastic (CRP), Glass Fibre Reinforced Plastic (GRP)
Brass, Copper & Bronze
Zinc
Wood
Different cuts of carbide burrs will likely be best suited to specific materials, start to see the next point below to find out about different cuts.
2. Carbide Burrs Commonly Appear in Two Cuts; Single Cut and Double Cut
Single cut (one flute) carbide burrs have a very right handed (Up cut) spiral flute. These are generally used with stainless steel, hardened steel, copper, certain, and ferrous metals and can remove material quickly which has a smooth finish. Use for heavy stock removal, milling, deburring and cleaning.
Heavy removing material
Milling
Deburring
Cleaning
Creates long chips
Double cut carbide burrs usually are suited for ferrous and non ferrous metals, aluminium, soft steel as well as for all non-metal materials like plastics and wood. They’ve got more cutting edges and will remove material faster. Double cut are now and again referrred to as Diamond Cut or Cross Cut (2 flutes cut across the other person) will leave a smoother finish than single cut because of producing smaller chips as they cut away the information. Use for medium-light stock removal, deburring, finishing and cleaning. A dual cut carbide burr is among the most popular cut and can see you through most applications.
Medium- light eliminating material
Deburring
Fine finishing
Cleaning
Smooth finish
Creates small chips
3. The many Shapes of Carbide Burrs and ways to Utilize them
Developer what contour around use is determined by the profile or cut you are planning to achieve.
These different shaped burs are certain to get into many a nook and cranny and create some interesting profiles.
carbide ball Burrs
Carbide Tree Burrs
Carbide Inverted Cone Burrs
Carbide Pointed Cone & Carbide Round Nose or Ball Nose Burrs
Cylinder Burrs. Round Nose/Ball nose/End Cut
Oval Burrs
Flame Burrs
Countersink Burrs
4. What Speed or RPM if you work with your Carbide Burrs?
The pace at which you use your carbide bur in your rotary tool will depend on the pad you use it on and the contour being produced however it is safe to say you don’t to exceed speeds of 35,000 RPM.
In the event the burs are chipping easily this can be as a result of speed being too slow. However, it’s ideal to get started on the bur off slow, helping the speed during this process. High speeds may prevent clogging inside the flutes of your burs.
5. Usually do not Apply An excessive amount of Pressure
As with most drill bits and burrs, permit the burr do the work and apply simply a little pressure otherwise the cutting edges of the flutes will chip away or become smooth too soon, decreasing the duration of your burr.
6. Carbide Burrs are Harder Than HSS Burrs
Our Carbide Burrs are machine ground from your specially chosen grade of carbide. Because of the extreme hardness with the Tungsten Carbide they are often used on a lot more demanding jobs than HSS (High-speed Steel).
Carbide Burrs also perform better at higher temperatures than HSS so you can run them hotter, and then for longer.
HSS burrs will begin to soften at higher temperatures so carbide is definitely a better choice for too long term performance.
7. Keep The Carbide Burr On The Move
When using your carbide burr do not ensure that it stays still for too long as this may prevent the burr from digging and jabbing into the material causing unsightly marks and roughness.
To learn more about SD-3 Carbide Burrs explore our new webpage